TCMD1000, tcmd4000 www.vishay.com vishay semiconductors rev. 2.2, 25-oct-12 1 document number: 83513 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 optocoupler, photodarlington output, high gain, single/quad channel, half pitch mini-flat package description the TCMD1000, tcmd4000 consist of a photodarlington optically coupled to a galliu m arsenide infrared-emitting diodes in either a 4 pin or 16 pin miniflat package. the elements provide a fixed distance between input and output for highest safety requirements. features ? low profile package (half pitch) ? ac isolation test voltage 3750 v rms ? low coupling capacitance of typical 0.3 pf ? low temperature coefficient of ctr ? wide ambient temperature range ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 appiclations ? programmable logic ?modems ? answering machines ? general applications agency approvals ? ul1577, file no. e76222 system code m, double protection ? csa 22.2 bulletin 5a, double protection ? din en 60747-5-5 (vde 0884-5) ?fimko ?bsi 17298_2 c e a c 4 pin 16 pin 1 2 8 9 c 17298 ordering information tcmd#000 part number agency certified/package ctr (%) ul, cul, fimko, bsi, vde > 600 sop-4 TCMD1000 sop-16, quad channel tcmd4000 absolute maximum ratings (t amb = 25 c, unless otherwise specified) parameter test condition symbol value unit input reverse voltage v r 6v forward current i f 60 ma forward surge current t p 10 s i fsm 1.5 a power dissipation p diss 100 mw junction temperature t j 125 c 7 mm s op-#
TCMD1000, tcmd4000 www.vishay.com vishay semiconductors rev. 2.2, 25-oct-12 2 document number: 83513 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes ? stresses in excess of the abso lute maximum ratings can cause permanent damage to the device. functional operation of the devic e is not implied at these or any other conditions in excess of those give n in the operational sections of this document. exposure to abs olute maximum ratings for extended periods of the time can adversely affect reliability. (1) related to standard climate 23/50 din 50014. (2) wave soldering three cycles are allowed. also refer to assembly instruction ( www.vishay.com/doc?80054 ). note ? minimum and maximum values are testing requirements. typical valu es are characteristics of the device and are the result of en gineering evaluation. typical values are for information only and are not part of the testing requirements. output collector emitter voltage v ceo 35 v emitter collector voltage v eco 7v collector current i c 80 ma collector peak current t p /t = 0.5, t p 10 ms i cm 100 ma power dissipation p diss 150 mw junction temperature t j 125 c coupler ac isolation test voltage (rms) v iso (1) 3750 v rms total power dissipation p tot 250 mw operating ambient temperature range t amb - 40 to + 100 c storage temperature range t stg - 40 to + 125 c soldering temperature (2) t sld 260 c electrical characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit input forward voltage i f = 50 ma v f 1.25 1.6 v junction capacitance v r = 0 v, f = 1 mhz c j 50 pf output collector emitter voltage i c = 100 a v ceo 35 v emitter collector voltage i e = 100 a v eco 7v collector dark current v ce = 10 v, i f = 0, e = 0 i ceo 100 na coupler collector emitter sa turation voltage i f = 20 ma, i c = 5 ma v cesat 1v cut-off frequency i f = 10 ma, v ce = 5 v, r l = 100 f c 10 khz coupling capacitance f = 1 mhz c k 0.3 pf current transfer ratio (t amb = 25 c, unless otherwise specified) parameter test condition part symbol min. typ. max. unit i c /i f v ce = 2 v, i f = 1 ma TCMD1000 ctr 600 800 % tcmd4000 ctr 600 800 % switching characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit rise time v ce = 2 v, i c = 10 ma, r l = 100 (see figure 1) t r 300 s turn-off time v ce = 2 v, i c = 10 ma, r l = 100 (see figure 1) t off 250 s absolute maximum ratings (t amb = 25 c, unless otherwise specified) parameter test condition symbol value unit
TCMD1000, tcmd4000 www.vishay.com vishay semiconductors rev. 2.2, 25-oct-12 3 document number: 83513 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 1 - test circuit, non-saturate d operation fig. 2 - switching times note ? as per iec 60747-5-2, 7.4.3.8.1, this optocoupler is suitable for safe electrical insulation only within the safety rating s. compliance with the safety ratings shall be ensured by means of protective circuits. typical characteristics (t amb = 25 c, unless otherwise specified) fig. 3 - forward voltage vs. ambient temperature fig. 4 - forward voltage vs. ambient temperature r l 50 channel ii channel i i c = 10 ma + v cc i f i f 0 r g = 50 t p t p = 50 s t = 0.01 oscilloscope r i = 1 m c i = 20 pf 14779 t p t t 0 0 10 % 90 % 100 % t r t d t on t s t f t off i f i c t p pulse duration t d delay time t r rise time t on (= t d + t r ) turn-on time t s storage time t f fall time t off (= t s + t f ) turn-off time 96 11698 safety and insulation ratings parameter test condition symbol min. typ. max. unit climatic classification iec 68 part 1 40/110/21 comparative tracking index cti 175 399 v iotm 6000 v v iorm 707 v p so 265 mw i si 130 ma t si 150 c creepage distance 5mm clearance distance 5mm insulation thickness, reinforc e rated per iec 60950 2.10.5.1 0.4 mm 0 50 100 150 200 250 300 0 40 80 120 p tot - total power dissipation (mw) t amb - ambient temperature (c) 96 11700 coupled device phototransistor ir-diode 0.8 0.9 1.0 1.1 1.2 1.3 0 20406080100 t amb - ambient temperature (c) 14389 v - forward voltage (v) f i f = 10 ma
TCMD1000, tcmd4000 www.vishay.com vishay semiconductors rev. 2.2, 25-oct-12 4 document number: 83513 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 5 - forward current vs. forward voltage fig. 6 - relative current transfer ratio vs. ambient temperature fig. 7 - collector dark current vs. ambient temperature fig. 8 - collector current vs. forward current fig. 9 - collector current vs. collector em itter voltage fig. 10 - collector emitter satura tion voltage vs. collector current 0.1 1 10 100 1000 0.0 0.4 0.8 1.2 1.6 2.0 v f - forward voltage (v) 14390 f i - forward current (ma) 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 - 30 - 20 - 10 0 10 20 30 40 50 60 70 80 90 100 t amb - ambient temperature (c) 14391 ctr - relative current transfer ratio rel v ce = 5 v i f = 1 ma 1 10 100 1000 10 000 100 000 20 30 40 50 60 70 80 90 100 t amb - ambient temperature (c) 14392 i - collector dark current, ceo with open base (na) v ce = 10 v i f = 0 0.1 1 10 100 1000 0.1 1 10 100 i f - forward current (ma) 14393 v ce = 2 v i - collector current (ma) c 0.1 1 10 100 0.1 1 10 100 v ce - collector emitter voltage (v) 14394 i - collector current (ma) c 1 ma 0.5 ma 0.2 ma 0.1 ma i f = 2 ma 0.6 0.7 0.8 0.9 1.0 1.1 110100 i c - collector current (ma) 14395 v - collector emitter saturation voltage (v) cesat ctr = 200 % used 25 % 50 % 100 %
TCMD1000, tcmd4000 www.vishay.com vishay semiconductors rev. 2.2, 25-oct-12 5 document number: 83513 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 11 - current transfer ratio vs. forward current package dimensions in millimeters 10 100 1000 10 000 0.1 1 10 100 i f - forward current (ma) 14396 v ce = 2 v ctr - current transfer ratio (%) 16283 possible footprint technical drawings according to din specifications 0.15 + 0.10 - 0.05 0.7 + 0.3 - 0.4 7 + 0.3 - 0.4 0.1 0.1 1 2 4 3 pin no. 1 identification 2.1 max. 1.9 2.8 max. 1.27 nom. 0.45 0.1 0.9 1.27 4.4 0.2 2.5 5 7.6
TCMD1000, tcmd4000 www.vishay.com vishay semiconductors rev. 2.2, 25-oct-12 6 document number: 83513 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package marking 7.6 5 4.4 0.2 1.9 1.27 nom. 0.45 0.1 7 + 0.3 - 0.4 0.7 + 0.3 - 0.4 0.1 0.1 0.15 + 0 .10 - 0 .05 1.27 0.9 specifications according to din technical drawings 10.12 10.4 max. 7 x 1.27 = 8.89 8.89 2.1 max. pin no. 1 identification issue: 1; 04.04.00 drawing-no.: 6.544-5330.03-4 possible footprint 16 15 14 13 12 11 10 9 12345678 15226 21764-15 md1000 v yww m 68 21764-16 tcmd4000 v yww m 68
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
